How to Clean Ratchet Straps and Store Them Right

Learn exactly how to clean ratchet straps step by step, dry and lubricate the ratchet mechanism, and store tie down straps to stop UV, mold, and rust damage.

TruckBro Tools QA Desk

11/19/20264 min read

How to Clean Ratchet Straps
How to Clean Ratchet Straps

A ratchet strap rarely fails because of one big event. It fails because road grime worked into the weave, the ratchet was put away wet, or the webbing spent a season cooking in the sun. The good news: cleaning and storing ratchet straps takes minutes, and a strap that is washed, dried, and coiled properly can serve two or three times longer than one thrown wet into a toolbox.

This guide covers when to clean, what to clean with, how to care for the ratchet mechanism, and how to store tie down straps so they are ready for the next job.

Why Cleaning Matters More Than You Think

Dirt is abrasive. Grit that works into polyester webbing saws at the load-bearing fibers every time the strap flexes. Salt from winter roads and fertilizer from farm jobs attack both the weave and the hardware. A strap can look fine, hold its color, and still have lost a meaningful share of its rated strength inside the weave where you cannot see it.

Cleaning removes the grit. Inspection proves the strap is still safe to use. Both take less time than replacing the load they were holding.

When to Clean Your Straps

  • After every muddy, sandy, or salty job — rinse the same day if possible

  • Before seasonal storage — never store a strap dirty for the winter

  • After chemical or fuel spills — immediately, and treat the strap as suspect until inspected

  • Before inspection — dirt hides cuts, broken stitching, and thin spots

How to Clean Ratchet Straps: Step by Step

[Figure — Four steps to clean ratchet straps from rinse to lubrication. Image file: fig3.png]

Caption: Rinse, wash mild, dry fully, wipe the hardware — the whole cycle takes about ten minutes per set.

  1. Shake off loose dirt and brush caked mud from the webbing with a soft brush.

  2. Rinse with clean water. A garden hose does the job. Never use a pressure washer — the jet drives grit deeper into the weave and can sever internal fibers you cannot see.

  3. Wash with mild soap if the webbing still looks dirty. Lukewarm water and a few drops of dish soap, scrubbed gently along the weave. Avoid bleach, solvents, and harsh detergents — they break down polyester polymers and quietly destroy the strap's rated capacity.

  4. Clean the ratchet hardware with a damp cloth. Open the handle fully and brush grit out of the gears and pawl. Compressed air blows debris out of the pivot area.

  5. Rinse and air dry completely. Hang the straps in a ventilated spot, out of direct sun. Dry the hardware with a cloth. Never coil or store a damp strap — trapped moisture breeds mold and rusts the spring.

Caring for the Ratchet Mechanism

The webbing usually survives years of service; the ratchet mechanism gives up first when it is neglected.

  • Lubricate with a silicone or PTFE dry spray, applied to the gears and pawl spring, then wiped off. Avoid oil-based products like WD-40 for storage — they attract grit and gum up the gears. (A light shot to free a stuck mechanism mid-job is fine; wipe it afterward.)

  • Check the pawl spring while lubricating. If it is rusted, weak, or the handle no longer locks positively, retire the hardware — a pawl that does not engage means the strap cannot hold tension.

  • Work the handle a few times after cleaning. Grit that survives in the gears grinds them flat over time.

How to Store Ratchet Straps Properly

[Figure — Correct coiled dry storage versus a wet tangled pile. Image file: fig4.png]

Caption: Coil from the loose end toward the ratchet, band it, and keep it dry, dark, and off the shop floor.

  1. Coil from the loose end toward the ratchet so the hardware ends up on the outside, protected.

  2. Band the coil with a hook-and-loop strap or a heavy rubber band. A tidy coil cannot tangle, and a tangle-free strap is one you will actually inspect before use.

  3. Store dry, dark, and ventilated. UV light is the silent killer of polyester webbing — noticeable fading means the fibers are weakening. A bin in the shop or a bag inside the cab beats a toolbox in the truck bed every time.

  4. Keep them off concrete floors and away from oil, fuel, and chemical storage.

When Cleaning Is Not Enough: Retire the Strap

Washing a damaged strap does not make it safe. Pull a strap from service if you find:

  • Cuts, frays, or broken edge yarns

  • Broken or pulled stitching at the hook ends

  • A knot tied into the webbing (a knotted strap loses a large share of its rated strength permanently)

  • Melted or hardened spots from friction heat

  • Corroded, bent, or cracked hooks and a spring that will not lock

  • Missing or unreadable WLL label

Our detailed guide on how to inspect ratchet straps walks through each wear point with photos, and our WLL explainer covers why the label matters legally. Note that different widths and lengths age differently — the sizing table in ratchet strap sizes helps you match replacement stock to the jobs the old straps were doing.

Quick Maintenance Schedule

  • Interval: After every dirty job — Rinse webbing, wipe hardware

  • Interval: Weekly (in service) — Visual check for cuts, frays, fading

  • Interval: Monthly — Lubricate ratchet gears with dry spray, test handle lock

  • Interval: Before winter storage — Full wash, complete dry, coil and band

  • Interval: Annually — Formal inspection against the retire list; discard failures

FAQ

Can I pressure wash ratchet straps?

No. High-pressure water drives grit into the weave and can cut internal fibers. A garden hose and soft brush clean just as well without the damage.

Can I put ratchet straps in the washing machine?

Not recommended — machine agitation and heat stress the webbing and hooks. Hand wash with mild soap and lukewarm water.

Is it OK to store ratchet straps in a truck toolbox?

Short term, fine. Long term, no — toolbox straps live with UV, moisture, and temperature swings. Bring them inside or use a ventilated bin.

Why do my ratchet straps smell musty?

They were stored damp. Mold weakens fibers. Wash with mild soap, dry fully in moving air, and store dry — any strap with visible mildew damage should be retired.

How often should I lubricate the ratchet?

About monthly for straps in weekly service, or after every wash. Use silicone or PTFE dry spray, never grease.

How to Store Ratchet Straps
How to Store Ratchet Straps

Subscribe to our newsletter

Email

sales@truckbrotools.com

logo
logo

CORE VALUES

  • Quality Craftsmanship

  • Safety First

  • Versatile Applications

  • Constant Innovation

  • Customer CommitmentCommon questions about MOQ, lead time and branding? Answers in our FAQ page or check our product catalogs.

GLOBAL STANDARDS

Professional cargo control solutions provider. High-quality tie downs, bungee cords, ropes and cargo securing products for the transportation industry. Anhui Langxi County Wantong Tool., Ltd. (factory) · Brand: Truckbrotools · Address: South Side of Provincial Highway 214, Xinfa Industrial Park, Langxi, Xuancheng, Anhui Province, China ·

T: 86-563-7651157 F:86-563-7651197

eason@truckbrotools.com