How to Secure a Ladder to a Truck Rack (Step by Step)

How to secure a ladder to a truck rack step by step: two ratchet straps, four tie points, the mistakes that let ladders slide, and when to re-check every time.

TIE DOWN

Eason

11/16/20263 min read

Step by step diagram showing how to secure a ladder to a truck rack with two ratchet straps and four
Step by step diagram showing how to secure a ladder to a truck rack with two ratchet straps and four

Why a Ladder Moves More Than You Think

A ladder is long, light, and has almost no flat surface to grip. On a truck rack it sits on two or three thin rails, and every bump turns the whole length of it into a lever. That is why a ladder that felt rock solid in the yard is often the first thing to slip on the highway.

Three things cause almost every ladder loss: the straps only hold the ladder down instead of pulling it forward and back, the tie points are in line with the ladder so it can slide along the rack, and the front end is left free to swing.

Pick the Right Strap for a Ladder

Thin ladder rungs and square rails cut into webbing. Use a 1 inch to 1.5 inch ratchet strap rated at 500 lb working load or more per tie, or a cam buckle strap if you prefer speed over tension. Never use a bungee cord as the only tie for a ladder.

  • Two ratchet straps as the primary tie, one over the front third and one over the rear third.

  • Two cam buckle straps as a backup, or for short trips across town.

  • Corner protection such as a strap sleeve or a folded pad where webbing meets the rack rail.

Four Points, Not Two

Two straps over the top only press the ladder down. A ladder can still walk forward under braking and slide back under acceleration. Add a strap that pulls the ladder toward the front of the rack, and one that pulls it toward the rear. Now the ladder is held in four directions and has nowhere to travel.

A quick test: grab the middle of the ladder and push it forward and back before you drive. If it moves at all, you are missing a fore and aft tie.

Step by Step: Tying a Ladder to a Truck Rack

1. Load it flat and inside the rails. Keep the ladder within the width of the rack and let it overhang evenly at both ends.

2. Hook the first strap to the rack rail behind the ladder. Run the webbing over the top of the ladder, down the far side, and back to the rail. The two ends of one strap should sit on opposite sides of the rail, not next to each other.

3. Ratchet until the webbing is firm, not crushing. You want the ladder to compress the rack slightly. Stop before the rail starts to bend.

4. Repeat at the rear third. Keep both straps at the same tension so the ladder does not twist.

5. Add the front and rear tie. Run a strap from the ladder end down to a low anchor at the front, and the same at the back, angled outward.

6. Tie off the tail. Roll the loose webbing and secure it with the strap keeper or a half hitch. A loose tail can whip and mark paint or find a wheel.

Common Mistakes That Cost Ladders

Strapping over the rungs only. Webbing can slip between rungs when tension relaxes. Strap over the side rails where the surface is continuous.

Anchor points that line up with the ladder. If both hooks are directly under the ladder, the load can pivot. Spread anchors wider than the ladder where possible.

Leaving the rear gate open. A ladder that slides back has nothing stopping it. Close the gate or add a rear stop.

Reusing a frayed strap. Check webbing for cuts, glazing, and loose stitching before every trip. A strap that has been chafed on a rack rail loses strength quickly.

Check It Again After Ten Minutes

New straps settle. Stop after the first ten minutes and re-check tension, then again at the first fuel stop. Most ladder losses happen early in the trip, before the webbing has taken its set.

Want the exact strap sizes for your rack and ladder length? Our team can match a set to your truck, and you can browse ratchet straps and cam buckle straps to compare working loads side by side.

Subscribe to our newsletter

Email

sales@truckbrotools.com

logo
logo

CORE VALUES

  • Quality Craftsmanship

  • Safety First

  • Versatile Applications

  • Constant Innovation

  • Customer Commitment

GLOBAL STANDARDS

Professional cargo control solutions provider. High-quality tie downs, bungee cords, ropes and cargo securing products for the transportation industry. Anhui Langxi County Wantong Tool., Ltd. (factory) · Brand: Truckbrotools · Address: South Side of Provincial Highway 214, Xinfa Industrial Park, Langxi, Xuancheng, Anhui Province, China ·

T: 86-563-7651157 F:86-563-7651197

eason@truckbrotools.com